mws020zgy 50 55 60 65 70 75 80 85 90 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. (33v) eff. (48v) eff. (75v) mws020ygy 60 65 70 75 80 85 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. (18v) eff. (24v) eff. (36v) technical specifications ? 20w standard package ? 100c case operation ? 3.3v output available ? integrated heat sink ? enable and trim pins ? wide range input voltage ? 1500v isolation ? short circuit protection description features efficiency vs. load (48v input) efficiency vs. load (24v input) mws dc-dc converters provide up to 20 watts of output power in an industry-standard package and footprint. the mws is available in either 24v or 48v input versions. with a maximum case temperature of 100c, the mws is well suited for the most demanding telecom, networking, and industrial applications. the mws features 1500 vdc isolation, short circuit, and overtemperature protection. turn-on time, max. 175 ms max. remote shutdown positive logic switching frequency 450 khz isolation input - output 1500 vdc temperature coefficient 0.015%/c case temperature operating range -40 to +100c storage range -40 to +105c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 5 g, 10 - 55 hz mtbf ? (bellcore tr-nwt-000332) 1.9 x 10 6 hrs safety ul, cul, tuv weight (approx.) 1.2 oz general notes ? mtbf predictions may vary slightly from model to model. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260c, ten seconds; fully compatible with commercial wave-soldering equipment. voltage range 24 vdc nominal 18 - 36 vdc 48 vdc nominal 33 - 75 vdc input undervoltage lockout <33v or <18v uvlo hysteresis 1v nominal reflected ripple 50 ma input reverse voltage protection shunt diode input setpoint accuracy 1.0% line regulation v in min. - v in max., i out rated 0.2% v out load regulation i out min. - i out max., v in nom. 0.5% v out minimum output current 5 % dynamic regulation, loadstep 25% i out pk deviation 4% v out settling time 500 s voltage trim range 10% short circuit / overcurrent protection shutdown / hiccup current limit threshold range, % of i out rated 110 - 140% output page 1 of 3 rev. dec 01, 2003 mws dc-dc series data sheet single-output, 20 watts
model input voltage input voltage maximum input output rated output ripple & noise typical (volts) range (volts) current (amps)* voltage (volts) current (amps) pk-pk (mv) efficiency** mws020zgy 48 33 - 75 0.77 54 75 81% mws020zhy 48 33 - 75 0.73 12 1.66 120 85% mws020yjy 24 18 - 36 1.34 15 1.33 150 85% notes: * maximum input current at minimum input voltage, maximum rated output power. ** at nominal v in , rated output.
thermal impedance tolerances pin function 1+ v in 2- v in 3 no pin 4 shutdown 5 no pin 6+ v out 7- v out 8 trim inches: (millimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 case: + 0.04, - 0.00 + 1.0, - 0.00 (dimensions as listed unless otherwise specified.) note: thermal impedance data is dependent on many environmental factors. the exact thermal perfor- mance should be validated for specific application. natural convection 11.5 c/w 100 lfm 10.2 c/w 200 lfm 8.5 c/w 300 lfm 6.5 c/w 400 lfm 5.4 c/w mechanical drawing model selection page 2 of 3 rev. dec 01, 2003 mws dc-dc series data sheet single-output, 20 watts
page 3 of 3 rev. dec 01, 2003 options this page is offered as a reference. consult factory for actual availability of options. when ordering equipment options, use the following suffix information. select preferred option(s) and add the suffix to the model number. ordering option examples are located below the options table. example options: hbs050zg-ant3v = hbs050zg-a with negative logic, lucent-compatible trim, and 0.95? vertical heatsink. les015yj-3n = les015yj with optional trim and enable, negative logic. qbs066zg-at8 = qbs066zg-a with lucent-compatible trim and 0.110? pin length. nuclear and medical applications - power-one products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divi sional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice. option suffix applicable series remarks negative logic n has, hbd, hbs, hes, hls, hld, les, ttl "low" turns module on qbs, qes, qls, tes, tqd ttl "high" turns module off lucent-compatible trim t has, hbd, hbs, hes, hls, qbs, qes, qls trim 1 ias, les enable 2 iad, ias, les, sms trim and enable 3 ias, les pin length and heatsink options standard pin length is 0.180" (4.6mm) 0.110" (2.8mm) pin length 8 all leaded models 0.150" (3.8mm) pin length 9 all leaded models 0.24" (6.1mm) horizontal heatsink 1h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.24" (6.1mm) vertical heatsink 1v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.45" (11.4mm) horizontal heatsink 2h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.45" (11.4mm) vertical heatsink 2v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.95" (24.1mm) horizontal heatsink 3h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.95" (24.1mm) vertical heatsink 3v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages)
|
